Steps to move a grand piano

Pianos routinely make movers yearly list of items that are most frequently harmed. Grand pianos are especially bothersome. Practicing the following procedures for disassembling, cushioning and loading grand pianos will avoid damage, lower claims cost, and improve consumer complete satisfaction.

1) At least three people are required to deal with an infant grand piano. If the baby grand piano requires to increase or down stairs or if a complete or performance grand piano needs to be carried, a minimum of four people are required.

2) Always finish a precise and thorough inventory. It might be preferable or needed to utilize a visual stock to sufficiently explain and show pre-existing damage.

3) As different parts are dismantled, please location all hardware in a properly labeled parts bag and then put the parts bag in a "Parts Box".

4) Eliminate the music rack (lyre) from its track by pulling it toward the keyboard. Wrap it in a tidy furnishings pad.

5) Disconnect the cover by eliminating the hinge pins. Have a single person wiggle the cover, holding it opposite the hinge, while a 2nd individual works the pin loose. Please be cautious not to harm the wood with the pliers or with the pin itself. If necessary, cover the jaws of the pliers with a small fabric to assist prevent damage to the wood. Wrap the cover in a tidy furnishings pad.

6) Eliminate the prop that holds the lid open and wrap it in a tidy furnishings pad. The prop has a hinge pin and remains in 2 pieces.

7) Eliminate the pedal assembly and wrap it in a tidy furnishings pad. The braces at the rear of the assembly rest in slots at each end. When removing the screws, please be mindful not to drop the braces. In addition, please be specifically cautious with the push-rods so that they will not get bent. As you face the piano, number the push-rods from delegated right as "1", "2", and "3", by placing a piece of masking tape with the proper number on each rod. Note: If masking tape is not available, please use properly labeled parts bags for this function. When reassembling at destination, please make certain to put the rods in the appropriate order so that the pedals will work effectively.

8) Pad the piano by placing a tidy rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the cover of the keyboard to prevent it from tumbling open while you manage the piano. Cover the top of the piano with 2 tidy furniture pads, neatly folded around the keyboard. Use rubber bands to protect the pads. Keep in mind: Please guarantee that the surface area of the piano is dust-free prior to padding it. Padding an extremely sleek surface that is dusty may trigger fine scratches, particularly on a black lacquer surface.

9) Position a piano board and connect the straps so that it is all set to get the piano. The raised brace on the piano board must be at the keyboard end of the piano.

10) Remove the left front leg by placing one individual beneath the piano at the left end of the keyboard. Be sure to have 2 people raising the corner of the piano while the 3rd person gets rid of the leg. Note: Please be sure to keep in mind which legs were gotten rid of from which positions because some pianos have legs that are not interchangeable.

11) Location the piano on the piano board by decreasing the "leg-less" end onto the board. Please make sure to raise the whole piano slightly while completing this maneuver to avoid excessive pressure on the remaining, attached legs as the piano ideas. Lift the piano to an upright position on the board. Note: Please guarantee that the soundboard is safe before raising. Be sure that the piano is centered snugly versus the brace at the end of the piano board. Keep in mind: Never ever leave the piano ignored. Constantly have at least one individual holding the piano stable at all times.

12) Get rid of the 2 staying legs and wrap them in clean furnishings pads. These legs are kept in place by a "crucial and slot" plan. To eliminate the leg, slide it inward toward the center of the piano till it comes out of the slot.

13) Protect the piano to the piano board by bringing the ends of the straps together and fastening them. Location folded burlap pads over the furniture pads but under the straps to offer additional security to the edges of the piano. To prevent the strap near the narrow end of the piano from slipping off, tie the loose ends of the two straps together.

14) To move the piano over a flat, level surface, tilt the piano and piano board and place a four-wheel dolly under the center of the piano board.

15) To move the piano up or down stairs, use the piano board as a skid. After adequately padding the stairs for security versus home damage, place the keyboard end of the piano towards the bottom of the stairs. Attach a bulge strap to the top end of the piano board to avoid the piano from slipping.

16) To pack the piano, leave it on the piano board and location it in a tier as the first base product with the keyboard dealing with the wall of the preceding tier. The finest place to fill the padded lid is between the piano and the preceding tier or in between the piano and the wall.

Grand pianos represent a substantial challenge, they can be moved without damage by using typical sense Get More Info and practicing the treatments noted above.

Leave a Reply

Your email address will not be published. Required fields are marked *